Turbo Decoder Hu 64 user guide MANUAL

turbodecoder hu64 label


Good to know IF YOUR  tool is original , Prodecoder or Chinese production. If you dont see the hologram protective sticker with information below please consider this user guide non valid! Use of non original locksmith equipment can damage the locks you try to open with!

This photo explain the parts of your turbo decoder, note that any vehicle opening tool wich is made in our company Luckylocks has same concept for it mechanical parts and once you learn their functionality then will be easy to use all of them applying the same recurring procedures!

turbo decoder hu64 elements explore
see turbodecoder hu64 elements
  • key profile – on this tool it is HU64 / silca identification code / and it is made to fit in any lock of Mercedes Benz automobiles from 2000 up to today
  • sliding pins – sliding moving mechanical components necessary to unlock and decode the locks mounted on MB vehicles
  • pin bar – on each side of the decoder we have mounted pin bars for insert and extract the instrument in and out of the locks
  • tension wheel – round fron segment od the turbo decoder handle to use it for apply tension forces / left & right /
  • pin activator wheel – it is conected with the pin bars to comand them in open or closed positions
  • turbo wheel – the back wheel of the tool handle wich do rotatuinal mouvements and put in action the pins during the opening procedures.

Opening procedure and important tips to follow:

Clean the lock with some light oil spray such as WD40 to remove all dirt accumulated over time.

To discover the lock orientation you need to use your turbodecoder instrument. Insert it after the turbo wheel was rotated to the right and the pin activator wheel is pushed all to the front! Take the decoder for the ring on the pin activator wheel and insert it carefuly in to the lock. Not necessary to force strong the tool , it will enter if the lock is in good mechanical conditions. Now pull back only the pin activator wheel and apply rotational force on the tension wheel to the left. In that moment start to rotate the turbo wheel to the left also and feel the rotation, it will be easy with no resistance and in some point you will feel a resistance on it. note where is it line pointed in the moment of the resistance begining. IF the line of the turbo wheel is before the first stop sector – your orientation is good and you can start the opening procedure. If that line is after the first stop sector please turn the turbo wheel all to the right , push to the front the in activator wheel and extract the decoder from the lock, reverse it and insert again. Now your tool is correctly orientated.

To open the lock please pull back the pin activator wheel , force the tension tool to the right and rotate the turbo wheel to the left till it line match to the first stop sector. Turn back the turbo wheel at the initial postion – all to the right. Loose the tension force on the tension wheel and check the lock. Now apply the force to the left on the tension wheel and repeat the rotation with the turbo wheel up to stop sector 1. Go back with it and loose the tension. Repeat those steps for 20 times.

If the lock is not open please increase the rotatuing of the turbo wheel to the second stop point. all the rest is the same. only stop point is changed from 1 to 2.

Do that for next 20 times and if no result – do all but stop at the sector 3 for 20 more times. In some moment uthe lock must be opened. Usualy we open the locks in second stop sector but off course that depend of the operator abilities or fo the lock code configuration.

Decoding of Mercedes Benz locks opened by TurboDecoder hu64

If you need to decode the lock you just opened with your tool please follow the instructions:

Once your tool turn the lock and it can be opened please do not remoove it. Keep the lock turnded to left or right but not in neutral. When you are in truned position please rotate the turbo wheel all to the left / line of it will point the stop sector 3 /. leave it there and jiggle the tool by follow the plane of the key profile. Then turn the turbo wheel all to the right, rotate the tool in the neutral lock position, push forward the pin activator wheel and extract it from the lock.

With the turbodecoder out of the lock please pull back the pin activator wheel / pins become visible / and totate the back wheel up to sector 3 

Now see the pins, calculate the pin deepths and by follow the side A and side B order write down the codedicovered. That is the mechanical code needed for cut and working mechanical key by insert that code in cnc locksmith machine.




THE LOCK CODE IS: 1121355344 

After the code reading you have to reset your sliding pins. That is necessary for open othe lock. Reset procedure can be made ONLY WITH THIS SET UP DEVICE HU64!!!

Correct step to do:

Push to the front the pin activator wheel, rotate all to the right the turbo wheel and then inject the calibrated needle part of your set up device into the hole wich is located under each pin on the edge of your key profile. There are 5 holes on each side of it. When you ingecj and pish the reset device the point of it needle will slide the pin and will stop automaticly when the pin arrive to it start position. Now your tool is ready for open one other MB lock.


VIDEO INSTRUCTIONS how to use turbodecoder hu64

Leave a Reply

please share your experience to help Turbodecoder comunity

Your email address will not be published. Required fields are marked *